banner

Air Compressors Leawood KS

Looking for Air Compressors in Leawood? We have compiled a list of businesses and services around Leawood that should help you with your search. We hope this page helps you find Air Compressors in Leawood.

The Home Depot
(913)648-7811
9600 Metcalf Ave
Overland Park, KS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(816)767-8807
4707 E Bannister Rd
Kansas City, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Lenexa/Kansas City, KS
(913) 599-2800
8645 Bluejacket Road
Lenexa, KS

Data Provided By:
The Home Depot
(816)322-2531
1306 E North Avenue
Belton, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(816)931-7434
111 E Linwood Blvd
Kansas City, MO
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(913)851-9961
8000 W 135th Street
Overland Park, KS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Home Depot
(816) 767-8807
4707 E Bannister Rd
Kansas City, MO
 
The Home Depot
(913)789-8899
5700 Antioch
Merriam, KS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(913)631-1005
15501 W 67th St
Shawnee, KS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(913)780-6933
20025 W 154th Street
Olathe, KS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided By:

HandymanWire -Tools Questions and Answers



Air Compressors

Air Compressors

Can you explain the difference between air compressors?

All pnumatic "air" tools are rated by volume = cfm "cubic feet per minute" and an operating = psi "pressure per square inch". Air compressors are also rated in the same way, as to what they can deliver. The more psi the less cfm.

Check out the tools that you will or may be using and then select a compressor accordingly. Keep in mind that using spay gun the pressure is may be lower than other air tools however cfm is much higher and it is used for a continous period of time, there for you may be concerned with tank size at least 25 gals. Although a smaller tank size will work, if the item you are painting is sizable e.g.,(a car)you will have to stop and wait for the compressor to catch up. This would leave overspray "dry dull areas" marks on your work piece.

PUMP The pump "compressor unit itself". It consist of pistons simlar to that in a car engine. Keep in mind there are two type of two cylinder pumps. (1) Is a twin-cylinder which is two cylinders of the same size which operate in oppositon cycles and (2)there is a twin-staged pump, this consists of a one large cylinder and one smaller cylinder (This pump is designed for a higher operating pressure). Either one would be fine for most use however if all things were simular I would pick the 2-stage.

DUTY CYCLE "The duty cycle is an operating cycle in % how much work to how much rest the equipment need, 30% is not uncommon. It sound like you are NOT going to be using this equipment all day everyday so the duty cycle is not a major factor.

MOTOR If you select a shop model, a compressor with a 5hp (min) 240v. If you select a roll around type 3hp (min) 120v (NOTE Use a dedicated circuit to plug in and keep your extention cords "if used" short as possible and heavy as possible 12ga.(min). Onelast thing, there are direct drive and belt drive. Both seem fine.
693

Pneumatics

Can I use a hydraulic cylinder as a air operated cylinder? How would I figure out how much it would lift safely?

Well...in theory....
However, realize that with hydraulics you are counting on the hydraulic fluids near incompressibility to move the piston. With air, you are pressurizing the cylinder, which will take much longer for any movement. The cylinder may leak by too much for air, while the fluid sealed the piston. And safety? I would say.. if you are not using it as it was designed.. you are taking safety in your own hands.... entirely.

The force generated is the air pressure you will use time the surface area of the piston. Basically.. Pounds /inxin X inxin = pounds of force...

Another answer:
Yes, you can use a hydraulic cylinder for air service assuming the cylinder if of recent vintage (10 yr. or less). Seals in a hydraulic cylinder are heavier duty then those for...

Click here to read the rest of this article from Handyman