banner

Air Compressors Sequim WA

Looking for Air Compressors in Sequim? We have compiled a list of businesses and services around Sequim that should help you with your search. We hope this page helps you find Air Compressors in Sequim.

The Home Depot
(360)582-1620
1145 W Washington
Sequim, WA
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 7:00am-8:00pm

The Wood Well
(877) 440-2643
PMB 290
Port Townsend, WA

Data Provided By:
Henery Do it Best Hardware
(360) 385-5900
218 Sims Way
Port Townsend, WA
 
Budget Blinds of Port Angeles
(360) 582-9200
492 W. Cedar St.
Sequim, WA
 
Swain's Outdoor
(360) 681-6561
551 W Washington St Ste 3
Sequim, WA

Data Provided By:
Edensaw Woods, Ltd.
(360) 385-7878
211 Seton Road 2nd location 3223 Third Ave, Seattle WA
Port Townsend, WA

Data Provided By:
Sequim - Auth Hometown
(360) 681-3079
232 Valley Center Pl
Sequim, WA
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9.5-19
Tue:9.5-19
Wed:9.5-19
Thu:9.5-19
Fri:9.5-19
Sat:9-18
Sun:23-16
Store Features
Mon:9.5-19
Tue:9.5-19
Wed:9.5-19
Thu:9.5-19
Fri:9.5-19
Sat:9-18
Sun:23-16

Sunset Do it Best Hardware
(360) 457-3369
518 Marine Drive
Port Angeles, WA
 
Clallam True Value Hardware
(800) 642-7392
216 E Washington
Sequim, WA

Data Provided By:
Enclume Design Products
360 385-6100
24 Colwell Street
Port Hadlock, WA
 
Data Provided By:

HandymanWire -Tools Questions and Answers



Air Compressors

Air Compressors

Can you explain the difference between air compressors?

All pnumatic "air" tools are rated by volume = cfm "cubic feet per minute" and an operating = psi "pressure per square inch". Air compressors are also rated in the same way, as to what they can deliver. The more psi the less cfm.

Check out the tools that you will or may be using and then select a compressor accordingly. Keep in mind that using spay gun the pressure is may be lower than other air tools however cfm is much higher and it is used for a continous period of time, there for you may be concerned with tank size at least 25 gals. Although a smaller tank size will work, if the item you are painting is sizable e.g.,(a car)you will have to stop and wait for the compressor to catch up. This would leave overspray "dry dull areas" marks on your work piece.

PUMP The pump "compressor unit itself". It consist of pistons simlar to that in a car engine. Keep in mind there are two type of two cylinder pumps. (1) Is a twin-cylinder which is two cylinders of the same size which operate in oppositon cycles and (2)there is a twin-staged pump, this consists of a one large cylinder and one smaller cylinder (This pump is designed for a higher operating pressure). Either one would be fine for most use however if all things were simular I would pick the 2-stage.

DUTY CYCLE "The duty cycle is an operating cycle in % how much work to how much rest the equipment need, 30% is not uncommon. It sound like you are NOT going to be using this equipment all day everyday so the duty cycle is not a major factor.

MOTOR If you select a shop model, a compressor with a 5hp (min) 240v. If you select a roll around type 3hp (min) 120v (NOTE Use a dedicated circuit to plug in and keep your extention cords "if used" short as possible and heavy as possible 12ga.(min). Onelast thing, there are direct drive and belt drive. Both seem fine.
693

Pneumatics

Can I use a hydraulic cylinder as a air operated cylinder? How would I figure out how much it would lift safely?

Well...in theory....
However, realize that with hydraulics you are counting on the hydraulic fluids near incompressibility to move the piston. With air, you are pressurizing the cylinder, which will take much longer for any movement. The cylinder may leak by too much for air, while the fluid sealed the piston. And safety? I would say.. if you are not using it as it was designed.. you are taking safety in your own hands.... entirely.

The force generated is the air pressure you will use time the surface area of the piston. Basically.. Pounds /inxin X inxin = pounds of force...

Another answer:
Yes, you can use a hydraulic cylinder for air service assuming the cylinder if of recent vintage (10 yr. or less). Seals in a hydraulic cylinder are heavier duty then those for...

Click here to read the rest of this article from Handyman