banner

Ceiling Fan Installation Burlington WI

This page provides relevant content and local businesses that can help with your search for information on Ceiling Fan Installation. You will find informative articles about Ceiling Fan Installation, including "Ceiling Fans Questions and Answers". Below you will also find local businesses that may provide the products or services you are looking for. Please scroll down to find the local resources in Burlington, WI that can help answer your questions about Ceiling Fan Installation.

Regional HVAC Inc
(262) 534-7330
108 N Front St
Burlington , WI
 
Sunset Mechanical
(847) 366-5412
N1373 Thistle Dr
Genoa City , WI
 
Boldt Contractors Incorporated
(262) 363-8466
639 Baxter Dr
Mukwonago , WI
 
Dowe & Wagner
(815) 678-3000
11215A Commercial Ave
Richmond , IL
 
Ralphs Heating & Air Cond Inc
(262) 679-0272
S83 W18336 Saturn Dr
Muskego , WI
 
H J Faust Incorporated
(262) 763-7866
5933 S Pine
Burlington , WI
 
Westenn Mechanical Contractors
(262) 723-4955
990 Koopman Ln
Elkhorn , WI
 
Southern Lakes Plbg & Htg Inc
(262) 723-6422
N 5860 US Hwy 12
Elkhorn , WI
 
E Z Air Inc
(815) 941-2665
410 Bedford Rd
Morris , IL
 
SITC Inc
(847) 845-7648
904 Main St
Antioch , IL
 

Ceiling Fans Questions and Answers


Wobbly

Wobbly ceiling fan

Was cleanin' ceiling fan for summer use, and now it wobbles. It hangs from a 17' ceiling with a 6' extension tube and the wobble is quite noticeable (enuff to make the chain of the lights to bounce back and forth between sconces). The extension moves freely and i don't notice any particular angle one way or the other, it looks level. What can I do to stop the wobble?
Oh..it has sealed bearings..so oiling is not an option.

No oiling isn't what you need. The fan wobbles because it is not balanced. Did you, by chance, knock a balancing weight off of it when you were cleaning it??

They sell balancing kits for these fans at lighting stores. Try there. You will need to add weight to one of the blades to smooth things out.

Balancing a ceiling fan

Does any have some helpful tips for balancing a ceiling fan. I have one that is approximately a year old that I cannot get balanced.

My ceiling fans came with clips and a small weight that you could attach to the top of the fan blade. I assume you have these. Place the weight on each fan blade, successively and spin the fan by hand. This way you should be able to tell which fan blade is in most out of balance. After you determine the fan blade to attach the weight, you adjust the weight along the blade (by trial and error) after allowing the fan blades to get up to operating speed (electrically). The further away from the motor housing, the greater effect, so start out with the weight close to the motor housing.

Ceiling fan wobble

We have vaulted ceilings and I was wondering if there is any way to stop our ceiling fan from wobbling. We bought one of the weight kits but one of the first things it tells you to do is check the distance between the ceiling and the blades. With a vaulted ceiling there's no way, it's going to be the same. What can I do?

What you can try is a little trial and error. Start with small weights, add them to one blade, and see what effect it has. It will either improve or make it worse of course. In addition, you can see where to go next. You may find you need to add a little weight to more than one blade. However, always start small first.


Installation

Installing Ceiling Fans

I want to install a ceiling fan in my bathroom but there is no Light Socket. I do have canister lighting in my bathroom. How hard is it to run electrical and add support beam?

Well not too hard if you have done it before or are relatively so inclined. You not only need to run power to it (from the canister light) but down to the switch in the wall to control it. If you have access above (in the attic?) it makes the job much easier.
As for the support beam, the new box can be bought with a metal bracket that easily mounts to the ceiling joists on either side of where you putting the fan.
If you are doing his yourself and would like some more specific guidance, let me...

Click here to read the rest of this article from Handyman