Heating Contractors Albany OR

This page provides relevant content and local businesses that can help with your search for information on Heating Contractors. You will find informative articles about Heating Contractors, including "Furnace Buying Guide". Below you will also find local businesses that may provide the products or services you are looking for. Please scroll down to find the local resources in Albany, OR that can help answer your questions about Heating Contractors.

Mikes Heating & Air Cond Svc
(541) 928-1804
113 41st Ave SE
Albany , OR
Woodward Heating Inc
(503) 448-4328
552 Main Street
Aumsville , OR
Rice Heating & A/C, INC.
(541) 757-8813
PO Box 1456
Corvallis, OR
ExtraordinAir Heating and Cooling
(541) 258-5119
37298 Skyline Rd
Lebanon, OR
Service, sales, installation of heating and air conditioning equipment
24 hr service
Prices and/or Promotions
Recieve 10% off your total service bill

AC & Heating by Chris Hickok
(503) 394-2689
38374 Highway 226
Scio, OR
Middleton Htg & Sht Mtl Inc
(541) 758-3358
610 SW Washington Ave
Corvallis , OR
Salem Heating & Sheet Metal
(503) 581-1536
1225 22nd St SE
Salem , OR
ExtraordinAir Heating and Cooling
(541) 258-5119
37298 Skyline Dr
Lebanon, OR
Service Sales Installation of heating and cooling equipment
24 hr service

ExtraordinAir Heating and Cooling
(541) 258-5119
37298 Skyline Dr
Lebanon, OR
Heat and Cool repair,sales,installation

Oregon Ducts Inc
(503) 364-7703
1258 Jory Hill Rd S
Salem, OR

Data Provided By:
Data Provided By:

Furnace Buying Guide

When you schedule quotes with various heating contractors to buy a furnace, you can be sure most of them will present you with three different features, each of them costing you more.
These features are:
  • higher efficiency
  • two stage operation
  • variable speed fan motors.


Most major manufacturer's offer standard efficiency (80% AFUE), high efficiency (90% AFUE), and ultra high efficiency (about 95% AFUE) models. Most furnaces over 10 years old are only 60-70% efficient. The AFUE efficiency rating refers to the percentage of the heat that the furnace creates that enters your house instead of escaping up the chimney. Older furnaces let the exhaust gases leave the furnace at temperatures much higher than 212F so that they rise quickly and so that the water in them does not condense into a liquid and rust the heat exchanger and chimney. 80% efficient furnaces have a second fan motor that can push the exhaust up the chimney at temperatures just above 212F. 90-95% efficient furnaces have a second stainless steel heat exchanger where heat is removed from the exhaust gasses until the water condenses into a liquid. Plastic chimney pipes must then be installed running out of the house.

High efficiency models cost about 50% more than standard models, but the energy savings usually pay for this extra cost in less than 10 years. So, except for homes with lower than average heating costs, high efficiency is usually a good investment.

Two stage operation

One of the most common complaints people have about their heating systems is that they leave uneven temperatures throughout the house. Most older furnaces only have one setting: full blast. On mild days, they briefly fire up and blast out hot air when the thermostat calls for heat. They don't come on again until the house gets a little too cold. This results in inconsistent temperatures over time. Their lower amount of time in operation also results in uneven temperatures from room to room, leaving some corners of the house uncomfortably chilly. A two stage furnace which will run on a lower burner setting most of the time will help alleviate these problems. It will also be quieter most of the time when running in its lower setting. Expect to pay about 15% more for a double stage furnace than a single stage model.

Variable speed DC fan motors

A variable speed DC fan motor responds to various sensor inputs to provide the optimal airflow rate. This results in more precise control of heat delivery.

Some homeowners prefer to run their furnace's fan continuously throughout the day. The flow of air this creates throughout the home can create a mild cooling effect on summer days and, like having two burner stages, can also help create more even temperatures throughout the home. A variable speed motor uses much less power when it is being run continuously. A standard AC motor will use over 300 watts when gently circulating air through a...

Click here to read the rest of this article from Handyman