Heating Contractors Leland NC

This page provides relevant content and local businesses that can help with your search for information on Heating Contractors. You will find informative articles about Heating Contractors, including "Furnace Buying Guide". Below you will also find local businesses that may provide the products or services you are looking for. Please scroll down to find the local resources in Leland, NC that can help answer your questions about Heating Contractors.

Air Medic Duct Cleaning
(910) 452-5686
P.O. Box 16138
Wilmington, NC

Data Provided By:
C C Dickson Co
(910) 763-8465
1939 Kent St Wilmington
Wilmington, NC
Climate Services Group Ltd
(910) 791-0480
1227 S 3rd St
Wilmington , NC
All Comfort Heating and Cooling
(910) 805-7621
202 Country Haven Dr
Wilmington, NC
Service, repair, installation
Membership Organizations
Home Service Team of North Carolina

Wren Heating & Air
(910) 763-1021
2113 Wrightsville Ave
Wilmington, NC
Comfort Solutions Inc
(910) 452-0740
115 Hinton Ave # 9 Wilmington
Wilmington, NC
Elliot's Air Purifiers
(910) 457-5552
311 River Dr Southport
Southport, NC
Regional Services Inc
(910) 443-5096
653 Birdie Ln
Southport , NC
MJ's HVAC Service
(910) 202-7239
114 D Yulan Drive
Wilmington, NC

Data Provided By:
DUCTZ of Wilmington, NC
(910) 799-2345
341-11 South College Rd
WIlmington, NC
NADCA Certified HVAC Restoration / Air Duct Cleaning
24 /7 Call anytime.
Membership Organizations
Prices and/or Promotions
Free Estimates

Data Provided By:

Furnace Buying Guide

When you schedule quotes with various heating contractors to buy a furnace, you can be sure most of them will present you with three different features, each of them costing you more.
These features are:
  • higher efficiency
  • two stage operation
  • variable speed fan motors.


Most major manufacturer's offer standard efficiency (80% AFUE), high efficiency (90% AFUE), and ultra high efficiency (about 95% AFUE) models. Most furnaces over 10 years old are only 60-70% efficient. The AFUE efficiency rating refers to the percentage of the heat that the furnace creates that enters your house instead of escaping up the chimney. Older furnaces let the exhaust gases leave the furnace at temperatures much higher than 212F so that they rise quickly and so that the water in them does not condense into a liquid and rust the heat exchanger and chimney. 80% efficient furnaces have a second fan motor that can push the exhaust up the chimney at temperatures just above 212F. 90-95% efficient furnaces have a second stainless steel heat exchanger where heat is removed from the exhaust gasses until the water condenses into a liquid. Plastic chimney pipes must then be installed running out of the house.

High efficiency models cost about 50% more than standard models, but the energy savings usually pay for this extra cost in less than 10 years. So, except for homes with lower than average heating costs, high efficiency is usually a good investment.

Two stage operation

One of the most common complaints people have about their heating systems is that they leave uneven temperatures throughout the house. Most older furnaces only have one setting: full blast. On mild days, they briefly fire up and blast out hot air when the thermostat calls for heat. They don't come on again until the house gets a little too cold. This results in inconsistent temperatures over time. Their lower amount of time in operation also results in uneven temperatures from room to room, leaving some corners of the house uncomfortably chilly. A two stage furnace which will run on a lower burner setting most of the time will help alleviate these problems. It will also be quieter most of the time when running in its lower setting. Expect to pay about 15% more for a double stage furnace than a single stage model.

Variable speed DC fan motors

A variable speed DC fan motor responds to various sensor inputs to provide the optimal airflow rate. This results in more precise control of heat delivery.

Some homeowners prefer to run their furnace's fan continuously throughout the day. The flow of air this creates throughout the home can create a mild cooling effect on summer days and, like having two burner stages, can also help create more even temperatures throughout the home. A variable speed motor uses much less power when it is being run continuously. A standard AC motor will use over 300 watts when gently circulating air through a...

Click here to read the rest of this article from Handyman