banner

Vinyl Flooring Grand Forks ND

Looking for Vinyl Flooring in Grand Forks? We have compiled a list of businesses and services around Grand Forks that should help you with your search. We hope this page helps you find Vinyl Flooring in Grand Forks.

B & L Hardwood Floor Services
(701) 746-1642
205 Fenton Ave
Grand Forks, ND
 
Steves Quality Flooring Service LLC
(701) 215-3010
609 6th Ave S
Grand Forks, ND
 
Curtis D Tile Installation
(701) 780-0860
809 N 5th St
Grand Forks, ND
 
Brians Flooring Inc
(218) 773-3130
1622 Central Ave Ne
East Grand Forks, MN
 
COUNTRY FURNITURE
(701) 235-7148
2801 S UNIVERSITY DR
Fargo, ND
 
Sterling Carpet One Floor & Home
(701) 746-8444
2030 32Nd Ave S
Grand Forks, ND
 
Grand Forks Glass & Paint
(701) 746-8444
2030 32nd Ave S
Grand Forks, ND
 
David Adams Hardwood Floor Sanding
(701) 746-9523
1211 Walnut St
Grand Forks, ND
 
Larry's Floorcoverings For Families, Inc.
(701) 772-8817
2524 S Washington St
Grand Forks, ND

Data Provided By:
CARPET WORLD INC
(701) 258-1968
501 AIRPORT RD
Bismarck, ND
 
Data Provided By:

HandymanWire - Vinyl FLoor Questions and Answers

The mastic you put down for the tile is thick enough that irregularities are easily covered.

They did tell you to rescrew the floor down, right? Use screws every eight inches along all the joists.

Removing Vinyl Flooring before Laying Tile



Could someone tell me what is the easiest or best way to remove vinyl flooring/glue and all. We're replacing it with ceramic tile and the entire vinyl flooring has been glued down.


Having just done this, I can honestly say.. there is no easy way. Here is what I dealt with. TO have it done professionally, no one would take up the vinyl for fear of asbestos. I didn't want to put anything on top, because I didn't want the extra height.. There are mastics for cementing the tile which can go over the plywood floor, if the the floor is sturdy enough (at least one inch of plywood between the sub floor and the underlayment) So I ripped it up, and scraped it with hand scrapers till I got pretty much everything up. It wasn't easy.. but it only took about one full day to do a 12x38 section of my house.

Linoleum Removal: Tools Needed and Height Added when Replaced w/Tile

I have two layers of linoleum in a small kitchen. I need to replace it with something as it is coming up in some areas and it is ugly!!! What do you think?

I will need a list of tools needed for the job if you think I should remove the linoleum. I read your comments to another person with the same problems and "grunt labor" is nothing I am looking forward to.

Can I only remove what is pulling up? If I leave it on what can I put over it? I was thinking about Ceramic tile. I have looked into it and seems to me that it will raise my floor another inch or more. Is that right? Is that normal and will it look ok around the cabinets and walls?

When I started looking into this.. I was where you are. I tried hiring the job out.. but no one would remove the old vinyl. I think there is too much fear of asbestos.. even though mine was asbestos free. (Yours may not be... if it is older than the 80's.. it probably has it) The pros solution was to cover everything with Luan plywood.. and start over. Well. that was for new vinyl. For tile.. it was another story.

Luan is not good for tile.. besides.. I too, did not like the thoughts of the raised floor. IF your floor is now.. 1 1/8 inches thick.. that is.. you have 1/2-inch subfloor.. and 5/8 inch underlayment.. of plywood.. you can go with tile over that. Ther...



Removing Vinyl Flooring to Lay Tile

We are trying to replace our vinyl flooring with tile, but are unable to remove the compound beneath the vinyl. The floors been there a really long time. The adhesive remover we bought at Home Depot, mineral spirits, etc. don't work at all.

Did someone tell you that you needed to remove all that compound? I just redid my floor, I had the same condition.. I removed everything that was loose and then tiled on top of everything. It has worked fine with no problems.

Click here to read the rest of this article from Handyman